The sensor should say that the goalkeeper absorbed about 216.998 J of energy when blocking the soccer ball, not accounting for wind and drag.
To calculate the energy absorbed by the goalkeeper, we can use the law of conservation of energy, which states that the initial energy of the ball before the kick is equal to the sum of the kinetic and potential energy after the kick and after the ball is blocked by the goalkeeper. We can assume that the ball is initially at rest before the kick, so the initial energy is zero.
The final kinetic energy of the ball after the kick can be calculated as:
[tex]KE1 = (1/2)mv1^2[/tex]
where m is the mass of the ball (converted to kg) and v1 is the velocity of the ball after the kick. Substituting the given values, we get:
[tex]KE1 = (1/2) (0.454 kg) (31 m/s)^2[/tex] = 218.147 J
The potential energy of the ball at this point is also zero since it is on the ground.
When the goalkeeper blocks the ball, the kinetic energy of the ball is transferred to the goalkeeper, so the energy absorbed by the goalkeeper is equal to the kinetic energy of the ball before it was blocked. The final kinetic energy of the ball can be calculated as:
[tex]KE2 = (1/2)mv2^2[/tex]
where v2 is the velocity of the ball after it is blocked and rolls back toward the player. Substituting the given values, we get:
[tex]KE2 = (1/2) (0.454 kg) (2.25 m/s)^2[/tex] = 1.149 J
The energy absorbed by the goalkeeper is then the difference between the initial kinetic energy of the ball and the final kinetic energy of the ball:
Energy absorbed = KE1 - KE2 = 218.147 J -1.149 J = 216.998 J
Therefore, the sensor should say that the goalkeeper absorbed about 216.998 J of energy when blocking the soccer ball, not accounting for wind and drag.
For more such questions on energy: brainly.com/question/8630757
#SPJ4
A 100g mass is swung around a tube 50 times in 1 minute calculate the centripetal force necessary to sustain this motion
The centripetal force of the object with a mass of about 100g will be 31.42 Newtons.
What is Centripetal force?A centripetal force is a net force which acts on an object to keep it in the state of motion along a circular path.
The angular velocity is defined as "the angle changing over time."
From the given of the problem:
m = 100g
rate of revolution = 50 rev / min
Therefore, using the formula:
angular velocity = rate of revolution x 2*pi / revolution
Angular velocity = (50 revs / min) x (2*pi radians / rev) = 100*pi radians / min
Centripetal force = mass × angular velocity
Centripetal force = 0.1 × 100π
Centripetal force = 31.42 Newtons
Therefore, the centripetal force will be 31.42 Newtons.
Learn more about Centripetal force here:
https://brainly.com/question/11324711
#SPJ9
Consider the circuit in the diagram below.
The switch at the top is moved to the closed or on position, the lightbulb glows brightly for a moment, and then dims gradually until it is fully dark. The switch on the top leg is then moved to the open or off position. The switch on the central leg is then moved to the closed or on position. What would happen to the bulb.
The light bulb would light up and stay constant.
The light bulb would light up and gradually dim.
The light bulb would gradually brighten.
The light bulb would flash on and then immediately shut off.
Answer:
The light bulb would flash on and then immediately shut off.
Explanation:
QuestionThe kelvin scale has its ________set to absolute zero which is the _________possible temperature that exists in the universe.AzeroBlowest
As one scale for another, both scales are connected. One unit on the Kelvin scale is equivalent to one degree on the Celsius scale. The zero points of the thermometer are the only distinction between these two scales.
What is the kelvin scale?Because the zero point is the absolute limit of how cold anything can become, the Kelvin temperature scale is also known as the absolute temperature scale. i.e., the temperature at absolute zero is [tex]-273[/tex]Degrees Celsius (0 K).
Absolute zero (0 K) on the Kelvin scale is the temperature at which a gas's volume is zero. Since it is below zero on all temperature scales, it is the lowest possible temperature. Thus, -273.15 oC is the Kelvin scale's zero.
With the non-scientific temperature scales, absolute zero isn't even zero. The temperature is -273.15 degrees Celsius, or -459.67 degrees Fahrenheit.
Therefore, The kelvin scale has its zero set to absolute zero, which is the lowest possible temperature that exists in the universe.
Learn more about kelvin scale here:
https://brainly.com/question/13290721
#SPJ4
EXPERIMENT: POLAR PROPERTIES
Perform the directions and Answer the following questions ….
These supplies are needed:
acetate (overhead transparency material) strip and tissue paper
vinyl strip and woolen cloth
slow, steady stream of water from a faucet
Follow these directions and answer these questions.
1. Rub the acetate strip with the tissue paper.
2. Bring the strip near a slow stream of running water.
What happened when the strip was brought near the stream?
From your ideas about charges on acetate and vinyl strips, predict what will happen if a charged vinyl strip is brought near the slow stream of water. (Review Unit 4.)
3. Test your hypothesis. Rub a vinyl strip with a woolen cloth.
4. Bring the charged strip near a slow stream of water.
HELP ASAP I NEED LEGIT ANSWERS:)
Charge is a fundamental physical property of matter that describes the degree to which it interacts with electromagnetic fields. It is an intrinsic property of subatomic particles, such as protons and electrons, that gives rise to electric and magnetic forces.
What is Charge?The basic unit of charge is the Coulomb (C), named after the French physicist Charles-Augustin de Coulomb, who first quantified the electric force between charged objects. A single proton or electron has a charge of approximately 1.6 x 10⁻¹⁹ Coulombs.
Rubbing the acetate strip with tissue paper transfers electrons from the tissue paper to the strip, giving the strip a negative charge.
When the negatively charged acetate strip is brought near a slow stream of running water, the water is attracted to the strip and bends towards it. This is because the water is polar, meaning it has a positive end and a negative end, and the negative end is attracted to the negatively charged acetate strip.
Predicted: When a charged vinyl strip is brought near the slow stream of water, the water should be attracted to the strip and bend towards it. This is because the vinyl strip is typically charged positively when rubbed with woolen cloth, so it will attract the negative end of the polar water molecules.
Rubbing the vinyl strip with a woolen cloth transfers electrons from the woolen cloth to the strip, giving it a positive charge. When the positively charged vinyl strip is brought near the slow stream of water, the water is indeed attracted to the strip and bends towards it, just as predicted.
To know more about vinyl visit:
brainly.com/question/27931267
#SPJ1
Worth 50 points, please answer quick.
A snowboarder stands at the edge of a 4.50 m high half-pipe. The mass of the snowboarder is 55.0 kg. What is the gravitational potential energy of the snowboarder?
Answer:
he gravitational potential energy of the snowboarder is 2532.5 J.
Explanation:
The gravitational potential energy of an object is given by the formula:
PE = mgh
where m is the mass of the object, g is the acceleration due to gravity, and h is the height of the object.
In this case, the mass of the snowboarder is 55.0 kg, the acceleration due to gravity is 9.8 m/s^2, and the height of the snowboarder is 4.50 m. So, the gravitational potential energy of the snowboarder can be calculated as:
PE = (55.0 kg)(9.8 m/s^2)(4.50 m) = 2532.5 J
So, the gravitational potential energy of the snowboarder is 2532.5 J.
Answer:
2425.5 J
Explanation:
The gravitational potential energy of an object can be calculated using the formula:
PE = m * g * h
where PE is the potential energy, m is the mass of the object, g is the acceleration due to gravity (9.8 m/s^2 on the surface of the Earth), and h is the height of the object above a reference point.
Plugging in the values, we get:
PE = 55.0 kg * 9.8 m/s^2 * 4.50 m = 2425.5 J
So the gravitational potential energy of the snowboarder is 2425.5 J (joules).
? switching is a technique to control general light levels by switching individual lamps or groups of lamps in a multi-lamp fixture separately.
Switching is a technique commonly used to control general light levels in buildings.
It involves the use of individual switches to control the lamps or groups of lamps within a multi-lamp fixture separately. This enables the user to control the amount of light produced in different areas of a room or building according to their needs. Switching can be done manually or automatically, using various technologies such as timers, motion sensors, and light sensors. It offers a simple and cost-effective way to improve energy efficiency and reduce energy consumption, as well as to create more comfortable and flexible lighting environments that meet the specific needs of different users. Switching is a technique commonly used to control general light levels in buildings.
Learn more about light :
https://brainly.com/question/15200315
#SPJ4
what causes the direction of the wind to change from day to night?
The direction of the wind is largely influenced by the temperature differences in the atmosphere.
During the day, the sun heats up the Earth's surface, causing the air to warm and rise, leading to the formation of a low-pressure area. As the air rises, cooler air from higher atmospheric levels moves in to replace it, causing wind to blow towards the low-pressure area.
At night, the Earth's surface cools down, leading to a drop in temperature, and the air cools and contracts. The air near the ground becomes denser and heavier, causing a high-pressure area to form. The cool and dense air sinks, displacing the warmer air, and creating wind that blows from the high-pressure area to the low-pressure area.
To know more about the winds, here
brainly.com/question/14570615
#SPJ4
A concave mirror is designed to have a magnification of 4 when an object is placed 60 cm in front of it.
What is the radius of curvature of the mirror?
Answer:
no answer
Explanation:
What is the name for a burst of activity on an EEG in the early stages of sleep?
gamma waves
sleep spindles
REM
lingering activation
The name for a burst of activity on an EEG in the early stages of sleep is "sleep spindle".
What is sleep spindle?A burst of brain activity during non-rapid eye movement (NREM) sleep is known as a sleep spindle and can be seen on an electroencephalogram (EEG). Although it can occur in other NREM sleep stages as well, it is a hallmark of Stage 2 sleep.
Sleep spindles are characterized by a burst of rhythmic brain activity that spans from 11 to 16 Hz and are short (often lasting only a few seconds). The thalamus, a region of the brain that is essential for transmitting sensory data to the cerebral cortex, is the source of this activity. The thalamus absorbs sensory input during sleep and modifies the information flow to the cortex, enabling the brain to filter out unimportant inputs and concentrate on significant ones.
To know more about sleep spindle visit:
https://brainly.com/question/13031857
#SPJ4
what can be used to describe electrical energy?
1.energy transferred through the movement of charges
2.kinetic energy of charged bodies in an electric field
3.potential energy stored in a battery
4.energy of light emitted by an electric bulb
energy transmitted by electric current
Electrical energy can be described as the energy transferred through the movement of charges, typically in the form of an electric current
define Electrical energy ?
Electrical energy is a form of energy that results from the movement of electric charges, typically in the form of an electric current. It is the energy that is transferred or converted from electric potential energy, which is the energy stored in a system due to the separation of charges. Electrical energy can be harnessed and used for various purposes, such as lighting, heating, powering electronic devices, and driving motors. It is an essential form of energy in modern society and plays a crucial role in many aspects of daily life.
The correct answer is 1. Electrical energy can be described as the energy transferred through the movement of charges, typically in the form of an electric current. Options 2, 3, and 4 refer to other forms of energy related to electricity but do not fully describe electrical energy itself.
To learn more about Electrical energy follow the given link: https://brainly.com/question/29789043
#SPJ1
what distinguishes the orbit of pluto from that of the eight major planets of the solar system?
Pluto's orbit is much more eccentric and inclined compared to the orbits of the eight major planets in the solar system. This means that Pluto's orbit is more elliptical and tilted relative to the plane of the solar system, while the orbits of the major planets are generally more circular and on the same plane.
First, Pluto's orbit is much more eccentric (elongated) than the orbits of the other planets. This means that its distance from the Sun varies more dramatically over the course of its orbit. While the other planets have nearly circular orbits, Pluto's orbit is more oval-shaped.
Second, Pluto's orbit is also more inclined (tilted) relative to the plane of the Solar System. The eight major planets all orbit in roughly the same plane, but Pluto's orbit is tilted at an angle of about 17 degrees. This means that it sometimes travels above and below the plane of the Solar System during its orbit.
Learn more about Pluto at https://brainly.com/question/13037755
#SPJ11
a spring whose equilibrium length is 6 m is compressed to a length of 1/2 m when a force of 15 n is applied. find the work done by the spring force while it is compressed to a length of 5 m.
A spring whose equilibrium length is 6 m is compressed to a length of 1/2 m when a force of 15 n is applied. 187.5 mJ is the work done by the spring force while it is compressed to a length of 5 m.
compression in spring x = 5m.
spring constant = 15 n/m
Magnitude of work done = Potential energy stored in spring W = 1/2 kx²
= 1/2 × 15 × 5 × 5
= 187.5 mJ
The spring's natural length is its length without any mass attached. We suppose that the spring obeys Hooke's law: if the spring's length is modified by an amount L from its natural length, the spring produces a force
Fs = kL,
where,
k is a positive quantity known as the spring constant.
F = -kx.
The spring constant is the proportional constant k. It is a measure of the stiffness of the spring. When a spring is stretched or compressed by an amount x from its equilibrium length, it produces a force F = -kx in the direction of its equilibrium position.
Learn more about Hooke's law from here; https://brainly.com/question/29126957
#SPJ4
The speeds of a car travelling on a straight road are given below at successive intervals of 1 second. Time/s Speed/m/s 0 0 1 2 2 4 3 6 4 8 Calculate a the average speed of the car in m/s b the distance the car travels in 4s c the constant acceleration of the car. 2 If a train travelling at 10 m/s starts to accelerate at 1 m/s² for 15s on a straight track, calculate its final speed in m/s.
a. the average speed of the car is 15 m/s.
b. the car travels 60 meters in 4 seconds.
c. the constant acceleration of the car is 2 m/s².
d. we find the the final speed of the train as 25 m/s.
How do we calculate?a)
We find the total distance traveled by the car as:
0 + 2 + 8 + 18 + 32 = 60 meters.
Average speed = Total distance / Total time
= 60 meters / 4 seconds
= 15 m/s
b) The distance traveled by the car in 4 seconds = total distance traveled
= 60 meters
c)
Acceleration = (Final velocity - Initial velocity) / Time
Acceleration = (Final velocity - Initial velocity) / Time
Acceleration = (8 m/s - 0 m/s) / (4 s - 0 s)
Acceleration = 8 m/s / 4 s
Acceleration = 2 m/s²
d.
Final velocity = Initial velocity + (Acceleration * Time)
Final velocity = 10 m/s + (1 m/s² * 15 s)
Final velocity = 10 m/s + 15 m/s
Final velocity = 25 m/s
Learn more about distance at:
https://brainly.com/question/26550516
#SPJ1
if a current of 4 a charges a dielectric for 3 s, how much charge is stored in the dielectric? round the final answer to one decimal place.
The required charge on the dielectric when current on it and time are specified is calculated to be 12 C.
The relation between current, charge and time is known to be,
i = q / t
where,
i is current
q is charge
t is time
Current on a dielectric is given as 4 A.
Time is given as 3 s.
Now, we should calculate the charge stored in the dielectric.
Making q as subject, we have,
q = i × t = 4(3) = 12 C
Thus, the required charge on the dielectric is calculated to be 12 C.
To know more about charge:
https://brainly.com/question/6031126
#SPJ4
the attraction of a person's body toward earth is called weight. the reaction to this force is the earth's surface pushing against the person's body. the person's body pushing against earth's surface. the person's body pulling on the earth. none of these
This is due to Newton's third law of motion.
The reaction to the force of weight on a person's body is the Earth's surface pushing against the person's body. This is known as Newton's third law of motion, which states that for every action, there is an equal and opposite reaction. When a person stands on the ground, their weight is exerted on the Earth's surface, and the surface responds by exerting an equal and opposite force on the person's body. This force is commonly referred to as the normal force. It is important to note that the normal force is perpendicular to the surface and is not the same as the force of friction, which is parallel to the surface and opposes motion.To know more about motion visit:
https://brainly.com/question/24132704
#SPJ1
If a meteor with a 20 m in diameter impacts Earth on land, approximately how big will the crater be?A. 200-400 m in diameterB. 500 to 1100 m in diameterC. 1000 to 1200 m in diameterD. 1300 to 1500 m in diameter
"If a meteor with a 20 m in diameter impacts Earth on land, approximately the crater is 200-400 m in diameter." Correct option is A.
A meteor is a small rock or piece of debris that travels through space and enters the Earth's atmosphere. When a meteor enters the Earth's atmosphere, it encounters friction and heat due to the atmospheric resistance, causing it to ignite and create a bright trail or shooting star in the sky. If a meteor is able to reach the surface of the Earth, it is called a meteorite.
When a meteor strikes a planet, there will almost certainly be a hole made at the site of impact. As the item moves more quickly, gets bigger, or is heavier, the crater will grow bigger. The meteor's mass and velocity are the best indicators of the magnitude of the impact crater.
The size of the crater created by a meteorite impact depends on many factors, such as the composition of the meteorite and the density of the material that it impacts. A crater with a dimension of 200–400 metres would be produced by a meteorite with a 20 m diameter.
To know more about craters:
https://brainly.com/question/30633492
#SPJ4
questions: 1. if you want to measure voltage across on a resistor connected to a 5v dc power supply, which two jacks of the dmm should be used? where do you set the function/range knob? which voltage range should be selected? 2. if the current flowing in a circuit is about 60ma. where should the function/range knob be set at in order to measure the current? which two jacks of the dmm will be used? what range should be used?
The voltage range should be selected to be at least 5V or greater to ensure accurate measurement and with the DMM placed in series with the circuit.
To measure the voltage across a resistor connected to a 5V DC power supply, you should use the red and black jacks of the DMM, where the red jack is connected to the positive side of the resistor and the blackjack is connected to the negative side. The function/range knob should be set to measure DC voltage (V~), and the voltage range should be selected to be at least 5V or greater to ensure accurate measurement.
If the current flowing in a circuit is about 60mA, the function/range knob should be set to measure DC current (A) and the range should be selected to be at least 200mA or greater to ensure accurate measurement. The two jacks of the DMM used, in this case, will be the red and black jacks, where the red jack is connected to the positive side of the circuit and the blackjack is connected to the negative side, with the DMM placed in series with the circuit.
Learn more about circuit
brainly.com/question/29745663
#SPJ4
) beam divergence. how accurately do you need to point your new satellite dish? directtv uses frequencies around 18ghz and dish antennas with a diameter of roughly 50 cm (~20 inches). give your answer in both radians and degrees. does this seem practical for a homeowner to install?
For a direct TV satellite dish with a diameter of roughly 50cm and frequency around 18 GHz, an accuracy of about 0.2 degrees of 0.0035 radians is required for reliable reception.
To accurately point a satellite dish the dish needs to be pointed in the direction of the satellite and at the correct angle to reciterecieve the signal. The accuracy required depends on the size of the dish , the frequency of the signal and the distance to the satellite.
For a direct TV satellite dish with a diameter of roughly 50cm and frequency around 18 GHz, an accuracy of about 0.2 degrees of 0.0035 radians is required for reliable reception. This level of accuracy is necessary to ensure that the dish is aimed at the satellite and is able to recieve the signal with enough power to provide a clear and stable picture.
While it is technically possible for a homeowner to install a satellite dish with this level of accuracy, it can be challenging for those without experience. There are many factors that can affect the installation, such as the location of the dish the mounting system and the cable routing. In addition, weather conditions such as wind and rain can affect the allignment of the dish.
To know more about Satellite dish go through:-
https://brainly.com/question/6344698
#SPJ4
1. if you want to measure voltage across on a resistor connected to a 5v dc power supply, which two jacks of the dmm should be used? where do you set the function/range knob? which voltage range should be selected?
Turn off the power supply and disconnect the resistor from the circuit. Set the function/range knob on the [tex]DMM[/tex] to the DC voltage (V) mode. Select the voltage range that is appropriate for the voltage. Since the power supply is [tex]5V DC[/tex], you should select a voltage range that is greater than 5V. Connect the red probe of the[tex]DMM[/tex] to the positive terminal of the resistor and the black probe to the negative terminal of the resistor.
Turn on the power supply. Read the voltage measurement displayed on the [tex]DMM[/tex]. Note that it is important to ensure that the probes are correctly connected to the circuit, and that the [tex]DMM[/tex] is set to the correct mode and range, in order to obtain an accurate measurement
To know more about Voltage, here
https://brainly.com/question/13521443
#SPJ4
Explain the applications of Newton’s law of motion to the concept of displacement, velocity and acceleration
Answer:
Newton's laws of motion describe the relationship between the motion of an object and the forces acting on it. These laws can be applied to the concepts of displacement, velocity, and acceleration as follows:
-First Law: The law of inertia
This law states that an object will remain at rest or in uniform motion in a straight line unless acted upon by an external force. This law implies that if there is no net force acting on an object, the object will remain at rest or in uniform motion in a straight line. In terms of displacement, this law means that an object's displacement will not change unless acted upon by an external force. In terms of velocity, an object's velocity will remain constant unless acted upon by an external force. In terms of acceleration, an object's acceleration will be zero unless acted upon by an external force.
-Second Law: The law of force and acceleration
This law states that the acceleration of an object is directly proportional to the net force acting on it and inversely proportional to its mass. In terms of displacement, this law means that the displacement of an object is directly proportional to the force acting on it. In terms of velocity, this law means that the change in velocity of an object is directly proportional to the force acting on it. In terms of acceleration, this law means that the acceleration of an object is directly proportional to the force acting on it and inversely proportional to its mass.
-Third Law: The law of action and reaction
This law states that for every action, there is an equal and opposite reaction. In terms of displacement, this law means that if an object exerts a force on another object, the other object will exert an equal and opposite force on the first object, resulting in a displacement. In terms of velocity, this law means that if an object exerts a force on another object, the other object will exert an equal and opposite force on the first object, resulting in a change in velocity. In terms of acceleration, this law means that if an object exerts a force on another object, the other object will exert an equal and opposite force on the first object, resulting in a change in acceleration.
In summary, Newton's laws of motion have numerous applications to the concepts of displacement, velocity, and acceleration. These laws can help us understand how objects move and how they respond to external forces. They are essential for fields such as physics, engineering, and astronomy, where the motion of objects is of critical importance.
Explanation:
Newton’s First Law of Motion
“An object at rest will stay at rest, and an object in motion will stay in motion unless acted on by a net external force"
This means that motion cannot change or decrease without the effect of an unbalanced force. If nothing happens to you, you will never go anywhere. If you’re going in a certain direction, unless something happens to you, you’ll always go that way forever.
That is, if the resultant force (the vector sum of the forces acting on the body) is zero, then the velocity of the object is constant. When we say that the velocity of an object is constant, we mean that both magnitude and direction are constant.
Examples
The electric fan continues to move for a period after the electricity is turned off.
Fall back forward when the stationary bus starts to move.
Newton’s Second Law of Motion
“If a force affects an object, the object gains acceleration, proportional to its strength and inversely proportional to its mass.”
Newton’s second law studies the movement of an object when external forces affect it. When a constant force affects a huge object, it causes it to accelerate, that is, to change its speed, at a constant rate.
In the simplest case, the force acting on an object at rest causes it to accelerate in the direction of the force. However, if the object is indeed in motion it may appear that the object is speeding up, slowing down, or changing its direction depending on the direction of force, directions taken by the object, and the frame of reference in which it is moving Relative to each other.
This relationship applies the principle of preserving the momentum, which is that when the sum of the resultant forces acting on the object is equal to zero, the momentum of the object remains constant. The resultant force is equal to the rate of change in the momentum.
This law also means that when two equal forces act on two different bodies, the object with greater mass will have less acceleration and slower motion, and the object with less mass has greater acceleration. For example, to illustrate:
If we have two similar engines, one for a large car and the other for a small car, then the small one will have more acceleration because its mass is less and the large one will have less acceleration because its mass is greater.
Newton’s Third Law of Motion
“For every action, there is an equal and opposite reaction.”
All forces in the universe occur in equal but oppositely directed pairs. There are no isolated forces; for every external force that acts on an object there is a force of equal magnitude but opposite direction which acts back on the object which exerted that external force.
In the case of internal forces, a force on one part of a system will be countered by a reaction force on another part of the system so that an isolated system cannot by any means exert a net force on the system as a whole. A system cannot “bootstrap” itself into motion with purely internal forces, to achieve a net force and an acceleration, it must interact with an object external to itself.
Engineers apply Newton’s third law when designing rockets and other devices, for example, the rush of gases from the rocket to the top when it ignites causes it to increase its speed.
When a person walks it affects the earth strongly and the earth also strongly affects it so both the earth and the person affect each other.
When you jump, your feet apply force to the ground, and the earth applies an equal and opposite reaction force that pushes you into the air.
When a person is in water, the water pushes the person forward while the person pushes the water back, both affect each other.
which one of the following energy conversion devices has the highest energy efficiency? group of answer choices incandescent light bulb automobile engine steam turbine generator
The steam turbine generator has the highest energy efficiency among the listed devices.
What is a steam turbine generator?A device that turns steam into energy is called a steam turbine generator. A generator and a steam turbine are its two major parts.
The steam turbine is an apparatus that turns a group of blades attached to a shaft using high-pressure steam. The steam expands as it moves over the blades, speeding up the shaft's rotation. The steam is then recycled for future use after being condensed back into liquid form.
An apparatus that transforms mechanical energy into electrical energy is a generator. The generator's rotor, which rotates inside a group of stationary coils while the steam turbine's revolving shaft connects to it, produces an electromagnetic field that generates an electrical current.
The energy conversion efficiency of a steam turbine generator can reach up to 50%, which is substantially higher than that of an incandescent light bulb or a car engine. Around 10% of the energy used by incandescent light bulbs is converted into visible light, with the remaining energy being wasted as heat. The average energy conversion efficiency of an automobile engine is roughly 25%, which means that only 25% of the fuel's energy is turned into usable work and the remaining 75% is lost as heat.
To know more about steam turbine generators, visit:
https://brainly.com/question/24322350
#SPJ4
You throw a rock horizontally off a cliff that’s 90 m high. How long will it take the rock to hit the ground?
what is the frequency of the oscillation? express your answer to two significant figures and include the appropriate units.
The frequency of the oscillation can be calculated as the inverse of the period: f = 1 / T = 1 / 4 units.
Based on the description, we can see that the waveform has a period of 4 units on the x-axis since it completes one full cycle over that distance.
Therefore, the frequency of the oscillation can be calculated as the inverse of the period:
f = 1 / T = 1 / 4 units
Expressing the frequency to two significant figures and including the appropriate units, we get:
f = 0.25 [tex]units^{-1}[/tex]
The frequency of this wave can be calculated by measuring the distance between two consecutive points of maximum amplitude, which in this case is one complete cycle.
Learn more about the oscillation at
https://brainly.com/question/30111348
#SPJ4
in this example, if the emf of the 4 v battery is increased to 17 v and the rest of the circuit remains the same, what is the potential difference vab ?
The potential difference Vab remains unchanged. Since the potential difference across the 4V battery is now 17V, the potential difference across the 12V battery is still 12V. The potential difference is still 4V.
Given the initial emf of circuit (V1) =4V
The battery is increased to (V2) = 17V
According to the Kirchhoff loop rule, the total current flowing into and out of a junction must equal one another. In other words, the sum is equal to zero. Using equation 1 and the Kirchhoff loop rule, we can calculate Vab (the voltage across ab) when the external magnetic field is 12 volts.
+12 - (I x 2) -(I x 3)-(I x 4)-(4)-(I x 7) = 0
I = 8/16 = 0.5 A
Vab = 4V + (I x 7) + (I x 4)
Vab = 4V + (0.5 x 7) + (0.5 x 4) = 4 +3.5+2 = 9.5 V
Using equation 1 and the Kirchhoff loop rule, we can calculate Vab (the voltage across ab) when the external magnetic field is 17 volts.
+17 - (I x 4) -(I x 3)-(I x 2)-(12)-(I x 7) = 0
I = 5/16 = 0.3125A
Vab = 17V -(I x 7) - (I x 4)
Vab = 17 - ( 0.3125 x 4)-(0.3125 x 7) = 17 - 1.25 - 2.1875 = 13.5625V
To learn more about potential difference click here https://brainly.com/question/12198573
#SPJ4
some appliances state the wattage on the back. this number may not match the meter reading from your experiment. why do you think this may happen?
The difference between the wattage stated on an appliance and the meter reading from your experiment could be due to inaccuracies in the appliance wattage rating, variability in power consumption, meter accuracy, or additional power consumption beyond the stated wattage.
There are a few reasons why the wattage stated on an appliance may not match the meter reading from your experiment:
Inaccuracy of the appliance wattage rating: The wattage stated on the appliance may not be accurate. This could be due to manufacturing tolerances or errors in the testing process. The actual wattage consumed by the appliance may be higher or lower than the stated rating.
Variability in power consumption: The power consumption of an appliance can vary depending on its usage. For example, a microwave may consume more power when heating food for a longer period of time compared to when it is heating for a shorter time. The wattage stated on the appliance may be an average value, while the meter reading may reflect the actual power consumed during your experiment.
Meter accuracy: The meter used in your experiment may not be accurate. Meters can have errors due to various factors such as age, calibration, or environmental conditions. This could lead to a difference in the reading compared to the wattage stated on the appliance.
Additional power consumption: Appliances may consume additional power beyond their stated wattage due to factors such as power surges, power factor correction, or standby power consumption. These additional factors may not be accounted for in the stated wattage, leading to a difference in the meter reading.
For more such questions on wattage
https://brainly.com/question/25781540
#SPJ4
when substances change state there is no change in mass. so for physical changes are generally easy to reverse though the end product may not always look exactly the same as the starting material. When a physical change occurs, the arrangement of particles within the substance may change, but the atoms in the molecules remain bonded together.
When substances change state, the molecules remain the same and there is no change in mass. This is because the molecules themselves do not break apart or form new chemical bonds.
What is molecules ?Molecules are particles made up of two or more atoms that are bound together. They are the smallest units of matter that can still retain the properties of the substance they are part of. For example, water is made up of two hydrogen atoms and one oxygen atom, which form a molecule. Molecules vary in size and complexity; some molecules, such as proteins, are made up of hundreds of atoms. Molecules are held together by chemical bonds, which are forces of attraction between the atoms. These bonds can be of several different types, such as covalent, ionic, and hydrogen bonds. Molecules can interact with each other and with other substances, such as solids, liquids, and gases, to create new substances with different properties. Understanding the behavior of molecules is essential to the study of chemistry, biology, and other sciences.
To learn more about molecules
https://brainly.com/question/28225015
#SPJ1
A spring extends by 10 cm when a mass of 630 g is attached to it. What is the spring
constant?
the spring constant was found to be as follows 61.74 N/m.
explain about spring constant ?
The spring constant, denoted by k, is a measure of the stiffness of a spring and is defined as the force required to extend or compress the spring by a certain distance. The formula for the spring constant is:
k = F / x
where F is the force applied to the spring and x is the resulting displacement. In this case, the spring extends by 10 cm when a mass of 630 g is attached to it, which means the displacement x is 0.1 m and the force F can be calculated as:
F = m * g
where m is the mass in kilograms and g is the acceleration due to gravity, which is approximately 9.8 m/s^2. Converting the mass of 630 g to kilograms gives:
m = 0.63 kg
So, the force F is:
F = 0.63 kg * 9.8 m/s^2 = 6.174 N
Now we can calculate the spring constant k:
k = F / x = 6.174 N / 0.1 m = 61.74 N/m
Therefore, the spring constant is 61.74 N/m.
To learn more about spring constant follow the given link: https://brainly.com/question/28196422
#SPJ1
a horizontal wire of length 3.0 m carries a current of 6.0 a and is oriented so that the current direction is 50o s of w. the horizontal component of the earth's magnetic field is due north at this point and has a strength of 0.14 x 10-4 t. what is the size of the force on the wire?
[tex]1.6 x 10^{-4} N[/tex] of magnetic force is exerted towards the Earth on wires carrying current. surface.
What is magnetic force?
When electrically charged particles are in motion, a magnetic force, attraction, or repulsion results from their motion. It is the fundamental force behind phenomena like how electric motors operate and how magnets are drawn to iron. Among fixed electric charges, there are electric forces; among moving electric charges, there are both electric and magnetic forces. The influence of a magnetic field generated by one charge on another charge can be referred to as the magnetic force between two moving charges. The direction of the magnetic force acting on a moving charge is at a right angle to the plane formed by the direction of the charge's motion and the direction of the magnetic field around it.
To learn more about magnetic force visit;
https://brainly.com/question/3160109
#SPJ4
what the coloring agents for some textile workers crossword?
The coloring agents used by textile workers are commonly referred to as "dyes."
Coloring agents are substances used to impart color to a variety of materials such as food, textiles, cosmetics, and plastics.
"A yellow food coloring commonly used in processed foods"
Tartrazine
"A blue food coloring commonly used in sports drinks"
: Brilliant Blue FCF
"A red food coloring commonly used in beverages and baked goods"
Allura Red AC
"A green food coloring commonly used in candies and chewing gum"
Fast Green FCF
To know more about Coloring agents here
https://brainly.com/question/29469125
#SPJ4
a 6 m high tree cast a 4 m long shadow. at the same time, a flag pole cast a shadow 50 m long. how long is the flag pole?
Using similar triangles, we can set up the following proportion:
height of tree / length of tree's shadow = height of flagpole / length of flagpole's shadow
Plugging in the values we know:
6 / 4 = x / 50
Solving for x:
x = 75
Therefore, the flag pole is 75 meters long.
How do you use the information about the tree and flag pole shadows to find the height of the flag pole?To find the height of the flag pole, we can use similar triangles. The tree and its shadow form one triangle, while the flag pole and its shadow form another. Since the two triangles are similar, we can set up a proportion: the height of the tree over the length of its shadow is equal to the height of the flag pole over the length of its shadow. We can then cross-multiply and solve for the height of the flag pole. Specifically, we can write 6/4 = h/50, where h is the height of the flag pole, and solve for h. This gives us h = 75 meters, so the height of the flag pole is 75 meters.
To know more about Triangles visit:
https://brainly.com/question/29083884
#SPJ4
