The indirect tire-pressure monitoring system is being discussed between two technicians. A technician claims that certain automakers have employed it.
According to technician B, in order to identify a low tyre, the rotating speeds of the rf and lr tyres are compared. The fact that BOTH technicians are accurate should not be overlooked. Indirect tyre pressure monitoring systems are those that do not use air pressure sensors inside the tyres (TPMS). Instead, they analyse relative wheel revolutions using the ABS wheel speed sensors to detect a low tyre. If the driver calibrates the system while any tyre is underinflated, the system will not report properly. The driver can calibrate the system by pressing a reset button on the dashboard or through the electronic controller.
Learn more about Tyres here:
https://brainly.com/question/28871929
#SPJ4
Increase 400 in the ratio 3:5
To increase the ratio 3:5 by 400, you can simply add 400 to each of the numbers in the ratio. The new ratio would be 403:505.
What is a Ratio?A ratio is a mathematical expression that compares the relative sizes of two or more values.
In ratio 3:5, the first number (3) represents one part and the second number (5) represents another part. These parts can be thought of as parts of a whole, where the whole is equal to the sum of the parts.
When you increase the ratio 3:5 by 400, you add 400 to each of the numbers in the ratio. This results in the new ratio of 403:505, which represents a new relationship between the parts.
The increase in the ratio by 400 means that each part has grown by 400 units, but the relative sizes of the parts have remained the same. The first part is still 3 times smaller than the second part, and the second part is still 5 times larger than the first part.
Read more about ratios here:
https://brainly.com/question/13513438
#SPJ1
A rectangle has a width of 8 m and a length of 7 m. How does the area change when each dimension is multiplied by 5? responses the area is increased by a factor of 5. The area is increased by a factor of 5. The area is increased by a factor of 10. The area is increased by a factor of 10. The area is increased by a factor of 25. The area is increased by a factor of 25. The area is increased by a factor of 50.
Answer:
The area is increased by a factor of 5.
Answer:
25
Explanation:
Sample 102-1s was taken at a depth of 5 centimeters beneath the surface of the soil. all sterile handling techniques were followed per operational procedures in section 5-3a. molecular isolation techniques identified six molecules for evaluation. these have been downloaded into canvas for your analysis. further chemical analysis of the sample conducted as part of the extraction process yielded the following information: all elements in the sample appear to be composed of protons, neutrons and electrons. all elements in the sample, isolated outside of their constituent molecules, are electrically neutral.
Collecting samples for DNA analysis from blood or other bodily fluids. DNA extraction is the process of opening up cells using heat or chemicals to release the DNA.
Purification of the sample through separation of cellular waste and other contaminants from the DNA. Establishing whether the sample is adequate for analysis — quantification employing the polymer chain reaction (PCR) to electrically order the fragment amplification while copying the DNA. The following are the steps involved in isolating and purifying DNA: sample gathering, extraction of DNA, and cleaning of the sample. DNA extraction and PCR DNA amplification quantification. Step 1: Collecting samples entails taking DNA from blood or other bodily fluids for examination. Step 2: DNA extraction involves cracking open the cells using heat or chemicals to release the DNA. Step 3: Purifying the sample entails separating the DNA from cellular waste and other contaminants.
Learn more about DNA here:
https://brainly.com/question/14973625
#SPJ4
water flows into the sink at a rate of 2 gal/min. if the drain is closed, the water will eventually flow through the overflow drain holes rather than over the edge of the sink. how many 0.4-in.- diamter drain holes are needed to ensure that the water does not overflow the sink? neglect viscous effects.
Therefore, roughly 12 drain holes with a diameter of 0.4 inches would be required to prevent the sink from overflowing with water.
Two gal of water per minute enter the sink. The water will eventually go through the overflow drain holes if the drain is closed as opposed to over the edge of the sink. number of 0.4-in.
Equation: The rate of flow through a circular hole can be determined.
[tex]Q = C \times A \times \sqrt{(2gH) (2gH)}[/tex]
Calculate the following to determine the cross-sectional area of a hole with dimension d:
[tex]A = \frac{\pi}{4} \times d^2[/tex]
To prevent the water from overflowing the sink, we can set the flow rate through each hole to be equal to the incoming flow rate and solve for the necessary number of holes.
[tex]n = \frac{2}{(0.61 \times \frac{\pi}{4} \times 0.16 \times \sqrt{(64.4 \times 6)})}[/tex]
[tex]= \frac{2}{(0.61 \times \frac{\pi}{4} \times 0.16 \times 2.51)}[/tex]
≈ 12
where,
2 gal/min
[tex]= n \times C \times \frac{\pi}{4} \times d^{2} \times \sqrt{(2gH)}[/tex]
Now,
[tex]n = \frac{2}{C \times \frac{\pi}{4} \times d^{2} \times \sqrt{(2gH)}}[/tex]
[tex]= \frac{2}{(0.61 \times \frac{\pi}{4} \times (0.4^{2}\ i\ n^2) \times \sqrt{(2 \times 32.2 \times H)})}[/tex]
[tex]= \frac{2}{(0.61 \times \frac{\pi}{4} \times 0.16 \times \sqrt{(64.4 \times H)})}[/tex]
Learn more about overflowing Visit: brainly.com/question/30558082
#SPJ4
where is the highest-altitude airport in the u.s.?
There will be several upgrades made to Leadville's Lake County Airport, which is located at an elevation of 9,934 feet; one of them is a brand-new runway that is 6,400 feet long. Colorado's Leadville Lake County Airport.
Which airport has the toughest landing conditions?Lukla has everything: mountains, strong winds, and a tiny runway. In Nepal's mountains, at the entrance to Mount Everest, a 1,729-foot runway is situated on a cliffside between two mountains and is frequently referred to as the world's most dangerous airport.
Is Colorado a turbulent flight path?As the jet stream passes through Colorado at these times of year, turbulence there is prone to be much worse. Stronger and more erratic airflow is produced as a result of the jet stream's acceleration and turbulence of the air.
To know more about Lake County Airport visit :-
https://brainly.com/question/11602799
#SPJ4
Write code that outputs variable numWeeks as follows. End with a newline
Ex: If the input is.
3
the output is
Weeks: 3
1 import java.util.Scanner;
2
3 public class Output Test I
4 public static void main(String[] args) {
5 int numileeks;
6
7 //Our tests will run your program with input 3, then run again with input 6.
8 //Your program should work for any input, though.
9 Scanner scnr = new Scanner(System.in); 12
10 numileeks = scnr.nextInt
11
12 Os System.out.println(numeeks+ "3"); Your code goes here
14 }
15 }
The correct answer is Create a statement that prints the numItems variable. Add a newline to end. The programme will be evaluated using various input values. import scanner from java.util;.
You should be aware that there are five different sorts of variables before we continue. local variables, class variables, instance variables, global variables, and constants. A constant is a piece of data whose value is fixed during the course of a programme. As a result, the value is constant, just as its name suggests. A variable is a piece of data whose value may change while the programme is running. Hence, just as its name suggests, the value might change. There are two uses for constants. An experimental investigation normally includes three different kinds of variables: controlled factors, dependent variables, and independent variables.
To learn more about numItems variable click on the link below:
brainly.com/question/14480279
#SPJ4
An equal-tangent sag vertical curve connects a 1% and 3% initial and final grades, respectively, and is designed for 70 mi/h. The high point on the curve is at elevation 822 ft. If the pvc is at station 110 00, what is the elevation of the curve at station 112 12?
A vertical curve with an equal-tangent crest is intended for 70 mph. The elevation of the high point is 822 feet.
The grade is first +1% and is ultimately +3%. What is the elevation of the curve at station 112+62 if the PVC is at station 110+00? Based on the stopping sight distance (SSD), calculate the design length of the vertical curve: L = KA, L = K X [G1 - G2], K = 247, L = 247 * [ 1- 3] = 494. Calculating the design curve radius is necessary to establish the design speed of an equal-tangent sag vertical curve. To do this, first figure out how long the curve is, which is the distance between the PVC and the PVI (101.77 miles minus 109.09 miles). The design curve radius in feet is then calculated by dividing the elevation difference between the PVC and the PVI (950 ft - 945 ft = 5 foot) by the length of the curve (1.77 mi) and multiplying by 100 (5 ft / 1.77 mi x 100 = 282.6 ft).
Learn more about Design curve radius here:
https://brainly.com/question/15392555
#SPJ4
Prove each of the following using proof by cases (hint: an integer is either even or odd). (a) n(n+1) is even, for all integers n. (b) 11n? +5n+1 = 0 has no integer solutions.
Each step should be explained by assuming that n is odd, that is, it is not even. The conclusion is refuted. After that, for some integer k, n = 2k + 1.
It is easy to understand how to make a contrapositive statement once one is familiar with the inverse statement. To get the inverse of the conditional statement, take the negation of the hypothesis and the conclusion. To generate the contrapositive of the conditional statement, first make the inverted statement, then switch the hypothesis and conclusion. 3.5n + 3 = 5(2k + 1) + 3 = 10k + 8 = 2(5k + 4). What is an even number? 1. Suppose that n is odd, that is, it is not even. The conclusion is refuted. 2. n is defined as an odd number when it equals 2k + 1 for some integer k. The definition of an even number in mathematics is 3.5n + 3 = 5(2k + 1) + + 3 = 10k + + 8 = 2(5k + 4) 5. As a result, 5n + 3 is even.
Learn more about Contrapositive statement here:
https://brainly.com/question/30590640
#SPJ4
Wind is becoming more common as a source of energy. Wind farms require large open spaces for the wind turbines. A negative consequence of this technology is wind turbines...a. are an inexpensive source of energy.b. cause little pollution to the environment.c. may hurt the flying animals in the area.d. are a renewable source of energy.
A renewable and clean energy source is wind power. The United States' top renewable energy source, wind, helps us lessen our dependency on fossil fuels.
How much room does a windmill require?Your wind turbine must be placed upwind of structures and trees, and it must be 30 feet above anything within a horizontal radius of 500 feet. Additionally, you need space to raise and lower the tower for maintenance, and if your tower is guyed, you also need space for the guy cables.
The most popular way to use wind energy is?The major purpose of wind energy today is to produce electricity. Windmills that can pump water were historically widely utilized in the United States, and some still function today on farms and ranches, mostly to supply water.
To know more about wind power visit :-
https://brainly.com/question/1311263
#SPJ4
if the allowable tensile stress for the bar is and the allowable shear stress for the pin is determine the diameter of the pin so that the load p will be a maximum. what is this load? assume the hole in the bar has the same diameter d as the pin. take t in. and w 2 in.
The formula for calculating maximal shear stress is V*Q / I*b. To put it simply, this is 12*V / 8bh. V stands for shear force, b for cross-sectional width, and h for cross-sectional height.
The value determined from spring's experimental data is the acceptable shear stress. Additionally, the value varies slightly depending on the substance. For instance, it is 50% for piano wire, hard drawn steel wire, oil tempered steel wire, and stainless steel wire, and it is 55%. A safety factor and the object's yield strength, or the stress at which the thing will be irreversibly damaged, are used to establish the allowable stress. As a result, determining the materials' yield strength is the first step in estimating allowed stress.
Learn more about stress here-
https://brainly.com/question/13261407
#SPJ4
Problems: 2.1 Find the number of equipotential common tie-points in Fig. 2-23: 2.2 Calculate current and current direction in Fig. 2-24(a) and (b): 2.3 For Fig. 2-25(a) and (b), find the unknown currents: Fig. 2-25 2.4 For Fig. 2-26a-d, find the unknown voltages: ig. 2. 3 (a) 2.5 For Fig. 2-27a-d find the unknown voltages and currents: 2.6 For Fig. 2-78a-c, find
R कq
at the terminals: 2.7 For Fig. 2-29a-d find all unknown currents (I):
2.8
For Fig. 2-30 a-d, find all equivalent resistances (Req): wi
sin
⋯
2.9 For Fig. 2-31 a-d, find all equivalent resistances (Req): 2.10 Attach a
10 V
load to the terminals and find the voltage and current across each resistor in the above circuits of Fig.
2−31
The correct answer is Have a look at Figure 1, which depicts the electric field lines of a single positive point charge in isolation. A positive charge emits electric field lines that.
Any computer emits RF (radiofrequency) waves as radiation. Except in cases where the intensity is strong enough to warm tissue, there is no evidence that these are detrimental (like a microwave oven). If you use your computer for longer than four hours every day, you are not putting yourself at risk (from radiation). Electromagnetic radiation is produced by computers. Namely, it produces visible light as electromagnetic radiation. Depending on the components of the computer, it is also possible for computers to generate other types of electromagnetic radiation, such as radio waves, ultraviolet light, and infrared light. One hour before going to bed, refrain from using them. Even if it is present in your bedroom, you are not required to utilise it. best that can be expected.
To learn more about emits electric click on the link below:
brainly.com/question/9446096
#SPJ4
The potential difference measured across a coil is 4. 5v,when it carries a direct current of 9a. The same coil when carries an alternating current of 9A at 25Hz,the potential difference is 24v. Find the current, the power and power factor when it is supplied by 50v,50Hz supply
When a coil is carrying a direct current of 9A, the potential difference across the coil is 4.5v. The potential difference between the same coil and a 9A at 25 Hz alternating current is 24v.
What is the coil's differential potential?The time rate of change of magnetic flux through a coil of wire is equal to the potential difference created across its ends. The term "induced electromotive force" refers to this potential difference.
How do you determine the difference's potential?When a charge q is transported from point A to point B, the potential difference between the two points, V = VB - VA, is defined as the change in potential energy of the charge multiplied by the charge.
To know more about potential difference visit :-
https://brainly.com/question/12198573
#SPJ4
Consider the following instance variable and method. Method wordsWithCommas is intended to return a string containing all the words in listOfWords separated by commas and enclosed in braces.For example, if listOfWords contains ["one", "two", "three"], the string returned by the call wordsWithCommas () should be "{one, two, three}".
Which of the following can be used to replace /* expression */ and /* condition */ so thatwordsWithCommas will work as intended?
A. / * expression * / / / * condition * /
listOfWords.size() - 1 / k != 0
B. / * expression * / / / * condition * /listOfWords.size() / k != 0
C. / * expression * / / / * condition * /
listOfWords.size() - 1 / k != sizeOfList - 1
D. / * expression * / / / * condition * /
listOfWords.size() / k != sizeOfList - 1
E. / * expression * / / / * condition * /result.length() / k != 0
In order for the sum Array to function as intended, the missing code should be replaced by the following statements: sum += sum + key[i - 1].
What is the Search and Replace command's shortcut?Tips: The keyboard shortcut CTRL + H can also be used to open the default Search and Replace window. It's wise to choose Replace rather than Replace All when replacing text.
Which of the following declarations of an array is correct?You can declare the array using the following syntax: The type of data you wish to include in the array is indicated by the data Type [] name Of Array. This could be a double, integer, string, or another type.
Top know more about Array visit:-
https://brainly.com/question/19570024
#SPJ1
Question 2 Generate four sinusoids with the following amplitudes and phases. Xi(t) = 5 cos (211 (15)t + 0. 51) X2 (t) = 5 cos (2n (15) t - 0. 25) x3 (t) = 5 cos (21 (15) t + 0. 411) X4 (t) = 5 cos (21 (15)t - 0. 9n) (a) Make a plot of all four signals over a range of t that will exhibit approximately 3 cycles. Make sure the plot includes negative time so that the phase at t = 0 can be measured. In order to get a smooth plot make sure that your have at least 20 samples per period of the wave. (b) Verify that the phase of all four signals is correct at t = 0 and also verify that each one has the correct maximum amplitude. Use subplot(3,2,i) to make a six-panel subplot that puts all of these plots on the same page. (c) Create the sum sinusoid via x5 (t) = x1(t) + x2(t) + x3 (t) + x4 (t). Make a plot of x5 (t) over the same range of time as used in the last plot. Include this as the lower panel in the plot by using subplot (3,1,3). (d) Measure the magnitude and phase of x5 (t) directly from the plot. In your lab report, include this plot with sufficient annotation to show how the magnitude and phase were measured. (e) Now do some complex arithmetic, create the complex amplitudes corresponding to the sinusoids x (t). Recall that x(t) = Acos(21864 +6)= Re{de'* ,254 Give the numerical values of 2, in polar and Cartesian form, where z = 4,21", i = 1,2,3,4,5 (t) Verify that x5 (t) = x1(t) + x2(t) + x3 (t) + x4(t). Show a plot of these five complex numbers as vectors. Relate the magnitude and phase of 3 to the plot of x (t) and explain
The cosine components to get the triangle's aspect are as follows: c = [a2 + b2 - 2ab cos C].
Where the triangle's edges are a, b, and c. The L is a remodel-pair that couples a DT sign with its continuous-frequency remodel and is primarily utilized in the assessment and design of DT systems. Lifestyles are essentially a way to ensure that the amount that constitutes a does not explode. It is easy to demonstrate this for sequences that can be summarized. The sum for n that ranges from minus infinity to plus infinity of x[n] instances e to the- j omega n in value is the same as the value of the at any factor omega if you take its value. Hence, F[cos0t] =[(0)+(+0)] is the Fourier transform of the cosine wave characteristic.
Learn more about Cosine here:
https://brainly.com/question/29891250
#SPJ4
Algorithmic trading is controlled and managed by human specialists trained in technology to validate every trade before it is sent to the market.a. trueb. false
Paul Krugerrand rejects the claim that although strategic trade policy is practicably achievable, it is theoretically impossible to implement.
It is true that in those situations there are winners and losers from trade, or in this case, more specifically, from the lack of trade, as Meeker town’s economy does not engage in international trade, forcing consumers to pay $33 for meeker rather than a price more in line with the global average of $35. The losers are the consumers, while the winners are the domestic producers. Consumers would profit if Meeker town allowed international trade because they could purchase cheaper meeker. According to Paul Krugerrand, an economic special interest group will hijack a strategic trade plan, causing it to be distorted and unlikely to be implemented. A special interest group is a group of people inside a larger organization who are committed to advancing a particular field of knowledge, field of expertise, or field of technology.
Learn more about Trade here:
https://brainly.com/question/15072048
#SPJ4
Give a simple description of the language generated by the grammar with productions S → aaA,
A → bS,
S → λ
With the same amount of a's and b's for each s, it can be represented as s1bs2 (and is possibly empty).
Because S and L are strictly shorter than L, the induction hypothesis is true for each Sisi, and we are done. Every collection of characters that a script interprets literally is called a string. The phrases "hello world" and "LKJH019283" are examples of strings. In computer programming, a variable is linked to a string. Generally speaking, a string in programming languages can either be all letters or all digits (alphanumeric). A string may be composed entirely of numbers, which is supported by many languages; however, in this instance, the string is commonly referred to as an integer. d. "a,b"*: the quantity of a's equals the quantity of b's, V equals S, A, B, a, b. ∑ = { a,b } R = { S → ε S SASBS. A SBSAS. A → a
Learn more about Strings here:
https://brainly.com/question/29856207
#SPJ4
when an emergency vehicle sounds its sirens or uses a flashing light, you
Answer:
must yield the right of way
Explanation:
if humidity sensors are not used to control humidity, ? can control humidity by taking advantage of the relationships between temperature and humidity.
Temperature sensors can use the relationships between temperature and humidity to control humidity if humidity sensors are not utilized.
What benefits do temperature and humidity sensors provide?These instruments are used to measure the actual humidity of the air at any given location or point. When air conditions need to be controlled for a variety of reasons or when they may be extreme, such devices are frequently used.
Why is it crucial to keep an eye on the relative humidity?Controlling moisture around a finished product is by far and away the most important reason to monitor relative humidity. This typically entails ensuring that the RH does not rise too high.
To know more about Temperature sensor visit :-
https://brainly.com/question/14258631
#SPJ4
What were the problems of building the Three Gorges Dam?
The building of the Three Gorges Dam on the Yangtze River in China was a significant engineering undertaking that faced numerous difficulties.
Among the major issues and difficulties encountered during the dam's construction are: Concerns about the environment: The damming of the Yangtze River would have a tremendous impact on the environment, potentially displacing millions of people, flooding vast swaths of land, and destroying ecosystems and wildlife habitats.
Geological risks: Due to the dam's location in a seismically active area, there have been worries regarding the dam's stability in the case of an earthquake. Technical difficulties: Building a dam of this magnitude and complexity posed serious technical difficulties that need mobilization.
Learn more about Gorges Dam Visit: brainly.com/question/11715443
#SPJ4
A worker was attempting
to correct an electrical problem involving two non-
operational lamps. He proceeded to the area where he thought the problem
was. He had not shut off the power at the circuit breaker panel nor had he
tested the wires to see if they were live. He was electrocuted when he
grabbed the two live wires and then fell from the ladder. What could have
been done to prevent this accident from occurring?
There are several things that could have been done to prevent this accident from occurring, including turning off the power, testing the wires, using appropriate personal protective equipment, etc.
What is safety procedure?A safety procedure is a series of directions or rules created to guarantee the security of employees in a specific working environment or while performing a specific task.
Several actions may have been taken to stop this catastrophe from happening, including:
Prior to attempting to work on the electrical system, turning off the power at the circuit breaker panel.Using a multimeter or a non-contact voltage tester, check to see if the wires are live.Protecting against electric shock by using the proper personal protection equipment (PPE), such as rubber gloves.Rather than attempting to do the electrical work yourself, have a certified electrician do it.Thus, the worker may have avoided the mishap and ensured a safe working environment by adhering to these safety procedures.
For more details regarding safety procedures, visit:
https://brainly.com/question/14480799
#SPJ9
The force exerted on the clothes during the spin cycle of an automatic washing machine is________
During the washing machine's spin cycle, the centrifugal force can be used to throw the water molecules on the clothes radially outwards because it acts along the radius.
How does a washing machine use centrifugal force?Your clothes are pushed toward the edges of the washing machine, which are frequently punctured with tiny holes, by this centrifugal force. After being pressed against the machine's sides, the force removes the water from your clothes.
What is the force that you apply to a machine?The input force or effort force is the force you apply to the machine. The term "output force" or "resistance force" refers to the force that the machine produces. By increasing either force or distance or changing the direction of force, a machine makes work simpler.
To know more about centrifugal force visit :-
https://brainly.com/question/17167298
#SPJ4
JAVAStatistics are often calculated with varying amounts of input data. Write a program that takes any number of non-negative integers as input, and outputs the max and average. A negative integer ends the input and is not included in the statistics. Assume the input contains at least one non-negative integer.Output the average with two digits after the decimal point followed by a newline, which can be achieved as follows:System.out.printf("%.2f\n", average);Ex: When the input is:15 20 0 3 -1the output is:20 9.50
An integer is a whole number without any decimal points, which can be positive or negative. Integers larger than or equal to zero are referred to as non-negative integers.
We can use a loop to continuously read integers from the user up until a negative number is entered in order to create such a program. The maximum and average of the non-negative integers entered are then computed while disregarding the negative integer. The largest integer in the set serves as the maximum. As we read in the data, we may utilize a variable to keep track of the greatest number. The variable will have the highest value when the loop is finished. The average is calculated by dividing the total number of integers by the sum of all the integer. We increase the count and add each non-negative integer to the total. We divide the sum by the count at the conclusion of the loop.
Learn more about Decimal here:
https://brainly.com/question/30656295
#SPJ4
Online analytical processing (OLAP) involves the analysis of accumulated data by end users. True oflr False
Problem 1.33 Item 7 Consider the interconnection shown in (Figure 1). The data for the interconnection are given in the table belovw Part A Element Voltage (V) Current (A) 900 105 600 585 120 300 585 165 -22.5 -52.5 -30.0 -52.5 30.0 60.0 82.5 82.5 Calculate the magnitude of the total power supplied. Express your answer to three significant figures and include the appropriate units. Psuppled885 mW Submit t Ans ure 1 of 1 X Incorrect; Try Again; 4 attempts remaining Part B Calculate the magnitude of the total power absorbed. Express your answer to three significant figures and include the appropriate units. er PabeobedValue Units Submit
The correct answer is Now that the three crucial components of an electric circuit have been described,... The watt (W) de- is the electrical unit of measurement for power.
A computer system's four primary equipment operations are input, processing, storage, and output. Transferring data into a computer system is referred to as input. When hardware fails, drivers become obsolete, or there is insufficient airflow because of clogged fans, a computer will crash. Malware, viruses, corrupted registry, bad sectors on the hard drive, and other factors can also cause your System to shut down suddenly. The display, power supply, or CPU is overheating are a few of the frequent causes of computer crashes. The computer's internal hardware is faulty. Hardware and software can't coexist.
To learn more about crucial components click on the link below:
brainly.com/question/29316066
#SPJ4
In terms of cars technology, does luxury equal safety, yes or no and why?
Since they are built to prevent collisions and offer more sophisticated safety and driver assistance features, luxury cars have a reputation for being among the safest automobiles on the road.
Are all automobiles similarly safe?Vehicles of all sizes are now safer because to advances in crash safety, yet even with these advancements, larger vehicles continue to be safer than smaller ones. Deaths in crashes decrease as vehicle size grows, as shown in the chart below.
What distinguishes expensive automobiles from everyday vehicles?Engines, transmissions, sound systems, telematics, safety features, and other equipment that aren't included in lower-priced models are frequently found in luxury cars, along with a plethora of other luxuries.
To know more about automobiles visit :-
https://brainly.com/question/1193772
#SPJ4
HDLC (High level Data Link Control) is?
Answer:
High-Level Data Link Control is a bit-oriented code-transparent synchronous data link layer protocol developed by the International Organization for Standardization.
Explanation:
An engineer troubleshooting a network connection identifies a port flapping problem. What should the engineer investigate as a possible cause? (Select all that apply.)
A.Port Security
B.Ethernet cable
C.NIC port
D.Switch port
An engineer troubleshooting a network connection problem identifies a port flapping problem.
The engineer should investigate the following possible causes:
A. Port security: If there is an incorrect port security configuration, it can cause port flapping problems.B. Ethernet cable: A faulty or damaged Ethernet cable can cause port overlapping problems.C. NIC port: A faulty or damaged NIC port can also cause port flapping problems.D. Switch port: A faulty or damaged switch port can also cause port flapping problems.Therefore, the engineer should investigate all of the above options as possible causes of the port flapping problem.
Learn More About network connection
https://brainly.com/question/28342757
#SPJ11
You've just put together a new team of 15 game developers from various cultures and backgrounds. Describe five possible cultural or social differences you might encounter in the workplace. Once you've identified the differences, explain how you might approach the situations and how you might be able to provide a solution that everyone is happy with.
The situations and how you might be able to provide a solution that everyone is happy with ; Language, Social norms,Values, Workplace hierarchy, Work styles.
What is the Social norms?Social norms are the unspoken rules and standards of behaviour that are generally accepted within a society. They are informal, unwritten guidelines that dictate how people should act in a given situation. They are generally accepted patterns of behaviour that are shared by members of a particular culture or group and provide a framework for understanding how to act in a particular context. Social norms can be enforced through informal sanctions such as social disapproval, or formal sanctions such as laws or punishments.
To learn more about Social norms
https://brainly.com/question/29522805
#SPJ1
Design a helical spring for an engine valve length of the spring when the valve in open in 45mm. and the length when closed in 55mm. spring load on the valve when open is 450N and when closed in 300N. Minimum internal diameter of the spring is 30mm. Take permissible shear stress = 400 N/mm2, and G = 0.8 x 105 N/mm2.
Hi dude how r u...........
If you've edited your source code file, you don't have to compile again before run to test, since the program last compiled is from the same file.a. TRUE
b. FALSE
The make command uses the gnu c compiler to compile source code into a binary programme.
An Integrated Development Environment, or IDE, is a piece of software that makes it simple for programmers to write, edit, compile, and run their applications. Syntax highlighting and automated code completion are two aspects of IDEs that make a programmer's job simpler.Notable Java IDEs available for many platforms and operating systems include BlueJ, JBuilder, IntellijIDEA, Eclipse, Netbeans, etc. One of the compilers in the GNU Compiler collection, the GNU C Compiler was made available by the Free Software Foundation. The GNU C Compiler is a completely *nix-oriented C language compiler that may be used by issuing instructions from its command line interface.
Learn more about C language here:
https://brainly.com/question/28232020
#SPJ4
